Diy Usb Ram Bluetooth Now That
Diy Usb Ram Install Finishes Theres
Diy Usb Ram Download Step 3

Diy Usb Ram Install Finishes Theres

Disregard the 30 minutes remaining and read a book or watch a movie because from this point untill the install finishes theres no user intervention required.

Some of you may see Build Your Own Mac and think, Oh, another Hackintosh.

How quaint. and move on to another Instructable.

This is a fully-functional Mac that you can build yourself for hardly any money, using used Macbook parts.

Benefits of building a DIY-intosh (thats what I call it) over a Hackintosh: - No need to do any EFI or kernel hacks to get it working.

Relatively) easy to get working because there are no bootloaders or hacks to install) - It can always use Apples updates because it doesnt require modifying Mac OS in any way.

Updates will never break the machine (unless Apple screws up big-time, which is highly unlikely).

Extremely small form factor.

Low-power (65W-90W PSU).

Extremely low-cost.

Diy Usb Ram Bluetooth Now That

My DIY-intoshs specs: - 2.0GHz Intel Core Duo - 2GB RAM (667 MHz) - 100 GB hard drive (7200 RPM) - 802.11 bgn wifi - Bluetooth Now that youve been fully convinced that you want to build a Mac, you can proceed on to the first step To see my original worklog and all the high-resolution pictures and HD video on my blog, visit.

Diy Usb Ram Download Step 3

Add Tip Ask Question Comment Download Step 3: Modify Case As Needed This means you just need to drill holes for cooling, a power button, ports, etc.

For example, I used my Dremel tool to cut some better ventilation holes.

Add Tip Ask Question Comment Download Step 4: Secure the Logic Board to the Case You can use either screws or glue.

I used hot glue because its easy, moderately strong, it has insulating properties, and I can remove it if necessary.

This includes the power switch, the DC-DC adapter, the Wi-Fi card and antennas, the Bluetooth module and antennas, the RAM, and the HDD.

After you insert the sleep switch into the logic board, you can glue the magnet to the top of the switch.

For wiring the power switch to the keyboard cable, see what this guy posted.

Those connections go to the momentary push-button to be used as the power switch.

One of the other pins is 5V, so if you connect a resistor and an LED to that and ground, you can have a power indicator.

I used a 220 Ohm resistor with a red LED to make my power indicator.

The battery connector must be connected to the logic board, and the magnet must be glued to the connector on the indicated area to trigger the sleep switch and to trick the MacBook logic board into believing its lid is closed.

Add Tip Ask Question Comment Download Step 6: Close It Up Close, but dont yet seal, the case.

I say this because you, like me, will probably forget to connect something and youll need to open the case again (bad Wi-Fi card, bad connections, etc.).

You should now see something like this: Add Tip Ask Question Comment Download Step 7: Install OS X: Gather Materials Ok, youve finished building the system.

You should probably connect it to a monitor, keyboard, mouse, and its PSU, just to check if the hardware works.

After a while (wait 10 minutes after booting), it should display a gray screen with a blinking folder icon with a on it.

Connect the Macs via firewire cable, plug Macs into wall power, connect DIY-intosh to monitor, connect USB keyboard and mouse to DIY-intosh, etc.

Add Tip Ask Question Comment Download Step 9: Boot Procedure If youre using a second Mac to install OS X on the DIY-intosh, follow these steps.

Add Tip Ask Question Comment Download Step 10: Vague Installation Procedure 1.) If you havent already done so, format the HDD to a Mac Journaled file system by selecting Disk Utility from the Utilities menu at the top of the screen.

Proceed through the installation.

Make sure that when you select a drive to install to, pick your DIY-intosh one and NOT your MacBook one.

Diy Usb Ram For Mac